The Mars Science Laboratory (MSL) rover carries 8 Hazard Avoidance Cameras (Hazcams). Two stereo pairs (one as a redundant backup) are mounted on the center of the front panel of the rover body with a boresight 68 cm above the base of the wheels. Two stereo pairs (one as a redundant backup) are mounted on the rear panel of the rover body with a boresight 78 cm above the base of the wheels; one pair is near the port side of the rover and the other pair is near the starboard side. Both front and rear Hazcams are pointed directly away from the rover 45 degrees off nadir. The redundant cameras are connected to the backup rover computer and are not expected to be used unless there is a problem with the primary rover computer and/or primary cameras. Each Hazcam pair assembly includes two cameras mounted to achieve a stereo view (a 16.6 cm stereo baseline for each of the front pairs, and 10 cm for each of the rear pairs). The Hazcams provide imaging primarily of the near field (< 5 m) both in front of and behind the rover. These cameras provide image data that are used by the rover computer to build range maps and perform onboard hazard detection and avoidance. They also support science operations for selecting near field targets and robotic arm operations. The Hazcams will be used to take images of the landscape that will help the rover avoid any obstacles in the way of the traverse. Each Hazcam consists of a detector head and an electronics box. The detector head houses an optical lens assembly and a Charge Coupled Device detector (CCD). The electronics box contains the CCD driver electronics, the 12-bit Analog to Digital Converter (ADC), camera/rover interface electronics, and a heater resistor that will keep the box above the minimum operating temperature of 218 K. The Hazcams use a broadband visible filter and produce 1024 x 1024 pixel images.

Instrument Overview
  ===================
 
    The Mars Science Laboratory (MSL) rover carries 8 Hazard Avoidance
    Cameras (Hazcams). Two stereo pairs (one as a redundant backup) are
    mounted on the center of the front panel of the rover body with a
    boresight 68 cm above the base of the wheels. Two stereo pairs (one
    as a redundant backup) are mounted on the rear panel of the rover
    body with a boresight 78 cm above the base of the wheels; one pair
    is near the port side of the rover and the other pair is near the
    starboard side. Both front and rear Hazcams are pointed directly
    away from the rover 45 degrees off nadir. The redundant cameras are
    connected to the backup rover computer and are not expected to be
    used unless there is a problem with the primary rover computer
    and/or primary cameras. Each Hazcam pair assembly includes two
    cameras mounted to achieve a stereo view (a 16.6 cm stereo baseline
    for each of the front pairs, and 10 cm for each of the rear pairs).
    The Hazcams provide imaging primarily of the near field (< 5 m) both
    in front of and behind the rover. These cameras provide image data
    that are used by the rover computer to build range maps and  perform
    onboard hazard detection and avoidance. They also support science
    operations for selecting near field targets and robotic arm
    operations. The Hazcams will be used to take images of the
    landscape that will help the rover avoid any obstacles in the way of
    the traverse.
 
    Each Hazcam consists of a detector head and an electronics box. The
    detector head houses an optical lens assembly and a Charge Coupled
    Device detector (CCD). The electronics box contains the CCD driver
    electronics, the 12-bit Analog to Digital Converter (ADC),
    camera/rover interface electronics, and a heater resistor that will
    keep the box above the minimum operating temperature of 218 K. The
    Hazcams use a broadband visible filter and produce 1024 x 1024 pixel
    images.
 
    Each camera (not including the cover) weighs 245 grams and uses
    approximately 2.2 Watts of power when the heater is not on. The MSL
    Hazcam design is identical in design to the Hazcams on the
    Mars Exploration Rovers, which are described in [MAKIETAL2003], with
    the exception of a more powerful 3.5 W heater on each MSL Hazcam and
    a protective cover.
 
 
  Instrument Objectives
  =====================
 
    The chief objectives of the Hazcams are:
 
    1) to support the operation of the rover on the surface of Mars by
    acquiring images of the terrain and landscape,
 
    2) to acquire images for support of auto-navigation, robotic arm
    operations, mobility planning (wheel sinkage and obstruction), and
    pointing of the ChemCam and Mastcam,
 
    3) to investigate the landing sites at cm/pixel resolution,
 
    4) to acquire images of the morphology of rocks and soil in order to
    provide clues about past geologic processes,
 
    5) to measure the distribution of rocks and soil around the rover as
    it moves from site to site,
 
    6) to calibrate and validate orbital remote sensing data, and
 
    7) to place rock and soil types encountered by the rover in a
    geological context.
 
 
  Calibration
  ===========
 
    The Hazcams have been calibrated over the flight range of
    temperatures. They were all calibrated with respect to geometric
    flat field response, detector dark current, camera absolute
    responsivity, detector noise performance, and detector gain.
 
 
  Detectors
  =========
 
    Each Hazcam uses a 1024 x 2048 pixel CCD with 12 micron-square
    pixels and a 100% optical fill factor. The CCDs operate in frame-
    transfer mode, dividing the detector into two regions. One of the
    regions is a 1204 x 1204 pixel photosensitive imaging region where
    the image is recorded. The other region is a 1204 x 1204 shielded
    storage region where the recorded image is shifted and stored during
    detector readout. It takes 5.1 msec to transfer data from the
    imaging region to the storage region, and 5.4 seconds for readout of
    data from the storage region. Each CCD includes 32 non-imaging
    pixels in the serial readout registers, which allow the monitoring
    of the CCD electronics offset and detector noise performance. The
    Hazcam CCD pixels have full well capacities of approximately 170,000
    electrons and are digitized at 12 bits/ pixel. The RMS read noise
    at cold temperatures (-55 degrees C) is approximately 20 electrons,
    and the detector system has gain values of approximately 50 e-/DN,
    which results in a system with approximately 0.5 DN of RMS read
    noise.
 
    The absolute quantum efficiency (QE) of the CCDs has been measured
    between 400 and 1000 nm at four operating temperatures ranging from
    218 K and 278 K. The QE of the MSL CCDs is typical of a silicon CCD
    detector, with sensitivity peaking at 700 nm with a QE value of
    approximately 43%. The SNR of the detector system is essentially
    Poisson-limited because of its low readout noise and small dark
    current rates in the Martian operating envirionments.
 
 
  Electronics
  ===========
 
    The Hazcam CCDs use a 'clocked antiblooming' readout technique,
    instead of having anti-blooming circuitry. The proper choice of
    autoexposure parameters prevent the blooming effect.
 
    The Hazcams also have the capability for onboard image processing.
    The Hazcams can do pixel summation in which they sum the rows and
    columns of an image, returning the results in a one-dimensional
    array of 32-bit integers whose length is the image height. These
    are very useful when the spatial content of an image has relatively
    low scene entropy and the emphasis is on the radiometry. The flight
    software (FSW) can also calculate and return the histogram of an
    image, which can be useful for atmospheric observations. Hazcam
    images can be spatially downsampled to a user-specified image size
    using one of a few techniques; nearest neighbor computation of the
    mean, computation of the mean with outlier rejection, and median
    averaging. The FSW also allows the option to downlink a subframed
    region of an image so full resolution can be downlinked at a lower
    data volume. The FSW is also capable of lossy and lossless
    compression of MER images. The rovers will use a ICER wavelet image
    compressor for the lossy and lossless compression.
 
 
  Filters
  =======
 
    The Hazcams use a combination of three filters (Schott OG590,
    KG5, and ND1.3) to create a red bandpass filter centered at
    650 nm and a FWHM of approximately 140 nm.
 
 
  Optics
  ======
 
    The Hazcams have f/15 cameras with a 5.58 nm focal length. The
    Hazcam optics are f-theta fisheye lenses with 124 degree x 124
    degree horizontal/ vertical field of view and a 180 degree diagonal
    field of view. They have an angular resolution at the center of the
    picture of 2.1 milliradians/pixel. The nominal exposure time for a
    noontime image on Mars is approximately .25 seconds. This time is 50
    times the frame transfer time of 5.1 ms. This ensures that the image
    signal is significantly than the image smear acquired during the
    frame transfer. The spectral range of the Hazcams is 600-800 nm.
 
 
  Covers
  ======
 
    Each Hazcam pair has a cover assembly with Lexan windows to protect
    the cameras from debris during descent and landing. After landing,
    before the Hazcams are used for imaging, the covers will pop open
    and never be closed again.

extracted metadata from PDS3 catalog and
                    modified to comply with PDS4 Information Model

Curiosity Hazcam

Description

Identifier (LID)

Version